How Do You Know When to Oil Your Alto Recorder
PHILIPPE BOLTON
HANDMADE RECORDERS & FLAGEOLETS
MAINTENANCE TIPS FOR WOODEN RECORDERS
Here are some suggestions for keeping wooden recorders in proficient condition.
one° PLAYING IN a new recorder
Wood needs to become accustomed to warmth & dampness caused by playing. You lot must therefore play in your musical instrument progressively, not exceeding the following fourth dimension limits:
| during the | you lot tin play for | |
| 1st week 2nd week 3rd calendar week 4th week | 10 minutes per day fifteen minutes per day 15 minutes per day 30 minutes per day |
Subsequently this flow you can increase the fourth dimension by reasonable steps.
From the beginning you can play all the notes, paying attention to tone quality and intonation.
2° CARE OF THE RECORDER
Practise not expose the recorder to excessive heat or cold, or to sudden temperature changes. Do not therefore leave it near a radiator, in direct sunlight, in a parked car... etc.
If it is cold, warm information technology in your hands before playing to limit condensation.
Afterwards PLAYING...
Carefully wipe out the bore with a material or piece of chamois leather. Suck dry out air into the windway through the beak, while closing the bottom end of the caput articulation with one hand, to remove some of the dampness there, and breathe information technology outside the recorder. Do this for i or ii minutes. Then let the musical instrument dry out out completely (especially the windway which cannot exist wiped) earlier closing its case. It is a adept idea to apply a represent this, and then that the pieces are held vertically.
If the dissimilar parts become impossible to separate afterwards a long playing session considering the joints take become clammy do non attempt to forcefulness them autonomously since this could cause damage. But wipe the inside as shown above and let them dry out completely. This can accept several hours, or even a twenty-four hour period or two. The instrument volition be easy to accept apart once information technology is dry out. To avoid this happening again take off a little thread or grease the articulation.
IF THE WINDWAY BECOMES BLOCKED Past CONDENSATION...
Since the instrument has been oiled during making, condensation may course in the windway afterward a few weeks. This tin can exist easily removed with detergent (h2o and washing-up liquid in equal parts + a niggling alcohol). Either take the cake out (see the page on advanced operations on the windway) and employ the liquid onto the windway and cake surfaces using a cotton wool bud, or, without removing the block, use a dropper to allow information technology flow into the window end while blocking the beak terminate with one finger. Wait for a few moments, then blow it out backwards through the bill while blocking the socket.
Click here for more detailed information on condensation in recorders
OILING...
Oil the recorder every iii months with linseed oil or every month with almond oil. The best tool for this is a bottle brush of the right bore which volition put a sparse layer of oil over the whole bore surface, simply y'all can also use a mop, a piece of cloth stock-still to a rod with a slit in the finish, or fifty-fifty a large feather to to practise the job. Yous tin too oil the labium sparingly with a cotton bud or modest paintbrush but NEVER the block and windway. Do not overoil.
| Allow the oil soak into the wood for a few hours, preferably keeping the instrument in a vertical position on a stand, then wipe away all the backlog in the bore and the holes that has not been absorbed. Y'all can apply wiping paper for this. |  |
THREAD JOINTS...
You can repair or adjust thread joints yourself. If they go too loose it is often sufficient to add a little thread. If they are as well tight you tin can take some off. For this you lot can use buttonhole silk or polyester which y'all wax with beeswax. Simply pull the thread across the wax. It should then stick to the joint. Exist careful non to put on too much thread or there could exist a risk of splitting the instrument. Cheque this by advisedly trying to assemble the recorder every bit y'all keep. After much apply it can go necessary to alter the articulation completely. Cut abroad the old thread without touching the wood, and wind on some new waxed thread (cf drawing below). Brainstorm past laying a loop lengthwise along the tenon, keep wrapping the thread effectually information technology, keeping the layer as regular as possible. Every bit before, be careful not to put on besides much. To secure the joint just pass the end through the loop and pull information technology back under the joint.
Thread joints that have been correctly fixed every bit shown above tin can be greased with vaseline or with a mixture of equal parts of vaseline and beeswax melted together in a jar heated in boiling water. Unfixed thread volition unwind if greased.
Click hither for a folio on recorder articulation maintenance.
Source: https://www.flute-a-bec.com/modempgb.html
0 Response to "How Do You Know When to Oil Your Alto Recorder"
Postar um comentário